A21-3 REVISED OCTOBER, 2012 © Copyright 2023. All rights reserved. No portion may be copied or reproduced in any manner. SOSMETAL PRODUCTS INC. FASTENERS & HARDWARE A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 OURUNI-TAP® and HOLLOW WALL ANCHORS UNI-TAP® WORKS IN: To Install: Drill a .281 size hole (K or 9/32 drill bit) Insert UNI-TAP® USE UNI-TAP® FOR: l Trailer liners, Truck panels, Refrigerated trucks, Reefers, Cold storage facilities, Food processing plants, Restaurants, Food preparation facilities l Electrical control panels and boxes l Telecommunications l Building and housing construction, wall and roof insulation l Plumbing and heating installations l Display signs HOLLOW PULL OUT PULL OUT PART GRIP MATERIAL CEMENT HOLLOW HEAD NUMBER SIZE RANGE SHEAR (LBS.) BLOCK (LBS.) WALL (LBS.) STYLE QTY 507395 1/4x1 3/16 to 1/2 250 150 130 Truss 100 507396 1/4x1-5/8 3/8 to 1-1/8 253 158 130 Truss 100 507397 1/4x2-1/8 7/8 to 1-5/8 274 154 130 Truss 50 507398 1/4x2-5/8 1-3/8 to 2-1/8 238 163 130 Truss 50 507399 1/4x3-1/8 1-7/8 to 2-5/8 228 150 130 Truss 50 All Sizes 5/8” 1/8” See Chart UNI-TAP® A unique nylon fastener that can be used in a variety of substrates. UNI-TAP® eliminates ice build-up, a common occurrence on the head of metal fasteners in refrigerated trucks and equipment. l Low cost, tamper resistant, vibration resistant, non-corrosive, sanitary, FDA approved. l Withstands temperatures from -60° F to 425° F. l High shear and tensile strength. Can withstand the impact of hammer installation and still hold firmly in place. And hammer into place l Wood l Concrete l Block Part No. 501641 180 pieces • 5 items 12061 steel tray Numbers in assortment 507395 507396 507397 507398 507399 TOGGLER® TOGGLE BOLTS When the application is critical use Toggler® Toggle Bolts, the strongest anchor available. l Hollow Block l Hollow Brick l Drywall l Cinder Block l Stucco l Paneling l Concrete Block l Plaster l Fiberglass l Cement Board l Boat Decks l Composite Panels l Easy to use - pre-installs without bolt. l Strongest toggle bolt available - size for size. l Accurate - rugged pre-installation mechanism centers metal channel in small hole, before bolt insertion. l Quick - can be used with a screw gun. l Cost effective - turn 2 person job into 1 person job. l Get job done faster - save 6 minutes per anchor compared with old-fashioned methods. l Convenient - enables removal of bolt/fixture without anchor falling behind wall. l Most reliable - will not damage or break through wall even when vibrated. l Ideal for heavy loads in hollow walls, ceilings and floors. l Grip range 3/8” to 3-5/8” wall thickness. l Toggle is zinc plated, straps and face plate are plastic. l Screw length = 1/2” + wall + fixture thickness. l Screws not included. Toggler® Toggle Bolts for maximum strength & precision alignment in: 3/16” & 1/4” Snap Toggle 3/8” & 1/2” Toggler Four easy steps to total anchoring security! Drill appropriate sized hole. Hold metal channel flat alongside plastic straps and slide channel through hole. With one hand, pull ring or hold ends of straps between thumb & forefinger. Pull toward you until metal channel rests flush behind wall. Slide plastic cap along straps until flange of cap is flush with wall. Place thumb between plastic straps. Push side ti side snapping off straps flush with wall. Insert bolt through item to be attached and tighten until flush with fixture. Minimum clearance behind wall: 1-7/8”. TENSILE PULL-OUT VALUES: LBS. AND (KG) PART 5/8” (16mm) CONCRETE 1/2” (13mm) HOLE GRIP NUMBER QTY SIZE DRYWALL BLOCK STEEL PLATE SIZE RANGE 507388 10 3/16-24 356 (162) 714 (325) 918 (417) 1/2 507389 10 1/4-20 306 (139) 925 (420) 1,283 (583) 1/2 3/8 - 3-5/8 507390 5 3/8-16 576 (262) 1,167 (530) 1,425 (648) 3/4 507391 5 1/2-13 N/A 2,038 (926) 2,392 (1,087) 3/4 3/8 - 2-1/2 Tests are ultimate load, industry safety standards recommend 1/4 of the values for actual application. Age and condition of wall material will cause tensile values to vary. l Brick l Plastic l Plexi-glass l Metal l Foam Insulation l Sanitary Wall Systems Part No. 501599 520 pieces • 15 items 12051 steel tray (with dividers) Numbers in assortment 27111 27119 27128 27146 408501 408502 408503 408504 507101 507102 507103 507105 507106 507116 507117 LIGHT & MEDIUM DUTY ANCHORS l Includes: nylon anchors, sheet metal screws, toggle wings and bolts. Used in plaster, wallboard, wood, masonry, concrete block, metal, and tile.
RkJQdWJsaXNoZXIy MzE1MDc=