B13-27 REVISED NOVEMBER, 2021 © Copyright 2023. All rights reserved. No portion may be copied or reproduced in any manner. SOSMETAL PRODUCTS INC. FITTINGS/HYDRAULICS/HOSE B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 WEATHERHEAD HOSE ASS. / AIR BRAKE FITTINGS PART INDUSTRY LENGTH NUMBER NUMBER 418353 W67157 27-5/8’’ AIR COMPRESSOR DISCHARGE HOSE - TEFLON DISCHARGE HOSE FOR GM BUSES l Replaces GM No. 2267157. 3/4’’ male pipe to flange. ** Includes 3/8’’ ABS to 3/8’’ male pipe adapter. 1/2’’ ID HOSE ASSEMBLY** * Includes 3/8’’ ABS to 1/4’’ male pipe adapter. 3/8’’ ID HOSE ASSEMBLY** l Low cost. l Ready to install. l Available in 9 different lengths. AIR BRAKE CHAMBER HOSE LINE Repairs break in hose near the valve or brake chamber. Replace and repair while on the road. l Swivel ends reduce residual torque in hose for longer life, no need to disconnect both ends to service brake system. l Installs easily in minutes with just a 5/16 hex key (key not included see page D11-6). l OE on 70% of trailer & tractor production. l Meets DOT 106 and J1402 requirements. l Used on 3/8” ID air brake hose with a min. 3/4” OD type A, AI and AIII. l All parts are non-corroding. l Fittings and retaining rings are brass. Hose barb and 2-piece shell are nylon. l Used by: Walbash, Freuehauf, Stoughton, Pines, Great Dane, Kenworth, Merit, Lufkin, Strick, Freightliner, Budd, and Brenner Tanks, etc. l Fittings are non-reusable 3/8” or 1/2” NPTF swivel ends. FIELD INSTALLATION KIT - FOR 3/8” ID AIR BRAKE HOSE Part No. 508500 2 With 3/8” NPTF Ends Part No. 508600 2 With 1/2” NPTF Ends Cutaway view of finished assembly. E-Z INSTALLATION Step 5. Insert BARB (E) into fitting. (Threaded end of barb should be greased.) Push and turn to start threads. Using a 5/16” hexagon key continue to push and turn until the barb is flush inside the fitting. NOTE: Check final assembly visually to insure that hose has not shifted position during assembly. (A) Shell (C) Shell (E) Barb (B) Fitting (D) Retaining Ring Step 2. Position hose end on SHELL (A) flush with groove (see arrows). Step 3. Insert FITTING (B) into groove and position shell (C) opposite SHELL (A). Step 4. With assembly in hand, squeeze forward ends of shells and push and twist RETAINING RING (D) over shells to its final position as shown by arrows. PART INDUSTRY LENGTH NUMBER NUMBER 418363 38353-01800 18-1/8’’ 418364 38353-02037 20-3/8’’ 418365 38353-02400 24-1/8’’ 418366 38353-02837 28-3/8’’ 418367 38353-03000 30-1/8’’ 418368 38353-03200 32’’ 418369 38353-03437 34-3/8’’ 418370 38353-03600 36-1/8’’ 418371 38353-04112 41-1/8’’ 3/8’’ Male Pipe Fitting 3/8’’ ABS (Air Brake Swivel) PART INDUSTRY LENGTH NUMBER NUMBER 418354 38166-01812 18-1/8’’ 418355 38166-02137 20-3/8’’ 418356 38166-02412 24-1/8’’ 418357 38166-02837 28-3/8’’ 418358 38166-03012 30-1/8’’ 418359 38166-03200 32’’ 418360 38166-03437 34-3/8’’ 418361 38166-03612 36-1/8’’ 418362 38166-04112 41-1/8’’ 1/4’’ Male Pipe Fitting 3/8’’ ABS (Air Brake Swivel) l Ready-made TEFLON® replacements for troublesome copper tubing running from compressor to reservoir. l Eliminate failures caused by vibration and heat. l Easy to install with standard brake nuts and sleeves. l No special fittings or adapters needed. ILLUSTRATION PART INDUSTRY LENGTH NUMBER NUMBER 1/2” hose ID - 1/2” tube size 418335 WTY824 24” 418336 WTY830 30” 418337 WTY836 36” 418338 WTY848 48” 5/8” hose ID - 5/8” tube size 418339 WTY024 24” 418340 WTY030 30” 418341 WTY036 36” 418342 WTY048 48” 5/8” hose ID - 3/4” tube size 418343 WTY224 24” 418344 WTY230 30” 418345 WTY236 36” 418346 WTY248 48” 1/2” hose ID - 1/2” tube size 418347 WTT824 24” 418348 WTT836 36” 5/8” hose ID - 5/8” tube size 418349 WTT024 24” 418350 WTT036 36” 5/8” hose ID - 3/4” tube size 418351 WTT224 24” 418352 WTT236 36” Step 1. Disassemble kit. l Replaces damaged hose ends of rubber air lines. l Made entirely of 100% brass for a long-lasting service life. l Complies with DOT 106 and SAE J1402 requirements. l All fittings are made and assembled in the USA. l Simple installation. l Stores easily in a glove or tool box. QUICK FIX HOSE END FITTING Part No. 508604 2 With 3/8” NPTF x 1/2 ID Hose Fittings PSS110221 PSS110321
RkJQdWJsaXNoZXIy MzE1MDc=