ADHESIVES and SEALANTS CHEMICALS SOSMETAL PRODUCTS INC. C11-6 REVISED JULY, 2015 © Copyright 2023. All rights reserved. No portion may be copied or reproduced in any manner. C15 C14 C13 C12 C11 C10 C20 C19 C18 C17 C16 C21 Part No. 711792 50 ml. bottle (1.69 fl. oz.) Meets Requirements: MIL Spec.: MIL-R-46082 Ford Spec.: WSK-M2G349-A6 Type III • Restores fit to worn areas up to .005". • Allows use and design of slip fit instead of press fit parts. • High viscosity. • Prevents corrosion. • Temp. range from -65°F to 300°F. • Replaces Loctite 680. HIGH STRENGTH, HIGH TEMP, SLEEVE RETAINER Part No. 711791 50 ml. bottle (1.69 fl. oz.) Meets Requirements: MIL Spec.: MIL-S-46082A Ford Spec.: WSK-M2G349-A5 Type II HIGH STRENGTH RETAINING COMPOUND Meets Requirements: MIL Spec.: MIL-S-46163A Ford Spec.: WSK-M2G361-A3 Type I, Grade K • Prevents loosening, locks & seals metal nuts, bolts/studs. • Resistant to gasoline, diesel, antifreeze, transmission fluid and oil. • Prevents galling & corrosion of threads. • Temp. range from -65°F to 300°F. • Replaces Loctite 262/271. Part No. 711785 6ml tube (.20 fl. oz.) Part No. 711784 50 ml. bottle (1.69 fl. oz.) Meets Requirements: MIL Spec.: MIL-S-46163 Ford Spec.: WSK-M2G351-A5 Type II, Grade N • For fasteners up to 3/4" dia. • Resistant to gasoline, antifreeze, transmission fluid and oil. • Prevents galling and corrosion of threads. • Removable with hard tools. • Apply prior to assembly. • Temp. range from -65°F to 300°F. • Replaces Loctite 242. MEDIUM STRENGTH REMOVABLE THREAD LOCK Part No. 711787 50 ml. bottle (1.69 fl. oz.) Meets Requirements: MIL Spec.: MIL-S-46163 Ford Spec.: WSK-M2G351-A1 Type III, Grade R MEDIUM STRENGTH “WICKING GRADE” POROSITY SEALANT THREAD LOCK • Maintains strength up to 450°F. • 3500 psi holding strength. • .015” gap fill capability helps tighten loose fitting assemblies. • Medium viscosity. • Prevents corrosion. • Temp. range from -65°F to 450°F. • Replaces Loctite 640. HIGH STRENGTH PERMANENT THREAD LOCK Color: GREEN • Thin consistency liquid wicks into threads. • Allows thread locking of in service devices. • Seals pinholes in welds, small cracks in metal housing & porosity in castings. • Resistant to solvents, oil, gasoline, diesel, grease & antifreeze. • Temp. range from -65°F to 300°F. • Replaces Loctite 290. Color: GREEN Color: GREEN Color: BLUE Part No. 711793 6ml tube (.20 fl. oz.) Part No. 711788 50 ml. bottle (1.69 fl. oz.) Color: RED PART WIDTH LENGTH NUMBER (INCHES) (INCHES) QTY 53720 1/ 520 6 53721 3/4 520 6 PART PERMATEX SIZE NUMBER NUMBER 812288 14A 1 oz. tube 812289 14D 16 oz. can 812290 14H 4 oz. can • Outperforms tape and pipe dope. • Temp. range: -60°F to +300°F. • Pressure rating: 0 to 5000 psi. • Solvent resistance: water, diluted acids, alkalies (10%), ethylene glycol & petroleum lubricating oil. TEFLON® THREAD SEALING TAPE Seals & lubricates all pipe fittings, including joints of dissimilar materials. Use on air, steam, oxygen, hydraulic, gas and refrigerant lines. Seals permanently, yet easy to disassemble. INDUSTRIAL HI-DENSITY STANDARD LOW-DENSITY • Color: Pink. • Density: 1.20. • Thickness: .0035-.0037. • Color: White. • Density: .700. • Thickness: .0032-.0034. • Withstands pressures to 10,000 psi. • Temp. range: –400°F to +600°F • Meets MIL-T-27730A. • Not affected by acids, gases, solvents, gasoline, oils or grease. • Non-flammable, non-toxic, will not dry out. • Never hardens in thread joint or can. • Lubricates threads for easy disassembly. • Pressure range use: Gases: up to 3,000 PSI Liquid: up to 10,000 PSI • Does not contain valve destroying grit. • U.S. Federal specs.: Meets and exceeds TT-S-1732 Part No. 53722 8 oz. brush top can THREAD SEALANT with Teflon® PART WIDTH LENGTH NUMBER (INCHES) (INCHES) QTY 53718 1/2 520 6 53719 3/4 520 6 THREAD SEALANT with Teflon® • The first threadlocker in a tape form. • No mess. no waste. • A must for every tool box. • Can be pre-applied for future assembly. • The same reliability & performance as Loctite® Removable Grade Threadlocking liquids. • Color: Blue. • Just peel, wrap, tear & assemble. Number of wraps required is dependent upon the size of the fastener. For a typical 3/8” bolt, 2 to 3 wraps are good. Part No. 837088 260” roll LOCTITE® THREADLOCKER TAPE Used in air, water, oil, gas & hydraulic systems. • Brushable to -50°F. • Carries the NSF seal. • No strong odor. • Soft set. • White paste. • Non-Toxic. Lubricates threads & prevents corrosion. (PSS070110) (PSS092016.53720.21)
RkJQdWJsaXNoZXIy MzE1MDc=