CHEMICALS SOSMETAL PRODUCTS INC. C15-6 REVISED JULY, 2015 © Copyright 2023. All rights reserved. No portion may be copied or reproduced in any manner. C15 C14 C13 C12 C11 C10 C20 C19 C18 C17 C16 C21 PRODUCT SPECIFICATIONS & APPLICATIONS Appearance: Clear Amber Liquid Odor: Solvent Odor pH: N/A Storage: Below 120°F (49°C) Boiling Point: <0°F — >200°F Vapor density: Above 1.0 Evaporation Rate: Fast evaporating Specific Gravity: (Water=1) .73 ∀.05 Solubility in Water: Negligible Part No. NPL202 • ADHERE• Super Stick Adhesive • Products Specifications Ingedients: Oxibismethane, Acetone, n-Hexane, Proprietary Resin, Methyl Ethyl Ketone APPLICATIONS AND USES Works extremely well on most surfaces, including foam, rubber, leather, paper, cloth, cardboard, mylar, foil, acetate sheets, glass and certain plastics. May react with urethanes. Test first. DIRECTIONS FOR USE Shake well before using. Always use extension nozzle. For soft materials, spray both surfaces, allow one minute to season before bonding. For hard materials - as above but allow longer seasoning before bonding. Temporary bonds: Apply a light, even spray to one surface only and allow tack to develop, then bond with firm pressure. After using, clear spray head and nozzle by turning can upside down and spraying a short jet of clear gas. FEATURES AND BENEFITS • Super sticky, high strength. • Bonds to metal, cork, rubber, plastic and other automotive materials. • Holds gasket in place — even overhead! • Resists water, anti-freeze, gasoline, oil, transmission fluid, brake fluid and grease. • Extension tube creates narrow spray — eliminates overspray and waste. Appearance: Black Odor: Solvent pH: N/A Storage: Below 120°F (49°C) Boiling Point: <0°F — >395°F Vapor density: Heavier than Air Evaporation Rate: Slower than Ether Specific Gravity: (Water=1) 1.10 ± 0.05 Solubility in Water: Nil Part No. NPL205 • SHIELD• Heavy Duty Black Rubber Coating • Products Specifications Ingedients: Calcium Carbonate, Asphalt, Toluene, Propane, Mineral Spirits, Butane APPLICATIONS AND USES For use on trucks, farm and construction equipment, in collision shops, as a tree wound dressing, and gutter and flashing sealer. Seals electrical boxes and fittings. Seals concrete and asphalt driveway cracks. DIRECTIONS FOR USE Shake well, until agitator moves freely. Spray 8 to 10 inches from a clean, dry surface in a sweeping motion. Dries to the touch in 1 hour, completely dry in 24 hours. For best results and optimum protection apply 2 coats. Wait 1-2 hours between coats. Remove overspray within 5 minutes using either kerosene or mineral spirits. FEATURES AND BENEFITS • An extremely durable rust and corrosion inhibitor. • Resists chipping and will not crack or peel with age. • Elastic, waterproof, deaden sound. • Paintable. Appearance: Red, Black, Aluminum, Clear Odor: Mild pH: N/A Storage: Below 120°F (49°C) Boiling Point: <0°F — >34°F Vapor density: Heavier than Air Evaporation Rate: Slower than Ether Specific Gravity: (Water=1) 1.32 ± 0.05 Solubility in Water: Nil Part No. NPL207 • SEALI-WIZ • Silicone Gasket Maker • Products Specifications Ingedients: Polymer, Silicone, Methyl Triacetoxysilane,Ethyl Triacetoxysilane, (Iron Oxide-Red only) APPLICATIONS AND USES SEALI-WIZwill adhere to clean metal, glass, most types of wood, silicone resin, vulcanized rubber, ceramic, natural and synthetic fiber as well as painted and plastic surfaces. Forms-in-place gaskets for oil and transmission pans, oil and water pumps, valve and timing chain covers, electric motors and electric control boxes, gear boxes, compressors, machine covers. DIRECTIONS FOR USE Surface must be clean, dry and free of oil, tar, dirt, and dust for best adhesion. Hold can at 45° angle and apply a continuous bead of 1/16” to 1/8” to the mating surface, encircling all bolt holes. For adhesion to both parts, assemble immediately. One part adhesion, allow 10 to 15 minutes for bead to skin. Assemble parts, but do not squeeze gasket out by over tightening bolts. Starts to cure immediately, fully cures in 24 hours and reaches optimum strength in 7 days. Leave a small bead of material which will form a sealing “plug” for reuse. To use, gently pull “plug” and begin to use material. If plug breaks leaving the dispensing tip sealed, use a paper clip or other wire object to remove and loosen the remainder of the cured material. FEATURES AND BENEFITS 100% RTV Silicone. Industrial strength. Caulks around tubs, sinks, showers. Temperature range from -60°F to 650°F. Insulates electrical components. Seals around windows, doors, walls. Binds most materials, similar or dissimilar (glass, wood, rubber, plastic, ceramics, etc.) Appearance: Clear Odor: Solvent pH: N/A Storage: Below 120°F (49°C) Boiling Point: <0°F — >156°F Vapor density: Heavier than Air Evaporation Rate: Slower than Ether Specific Gravity: (Water=1) 0.71 ± 0.1 Solubility in Water: Nil Part No. NPL213 • SPIDEY• Super Bonding Trim Adhesive • Products Specifications Ingedients: Propane, Hexane, Isohexane Isomers, Cyclohexane, Acetone, Amorphous Silica APPLICATIONS AND USES For use on leather, cork, wood, vinyl, paper, metal, cardboard, plastic, film, rubber, glass, cloth, foil, and foam. DIRECTIONS FOR USE Use at room temperature. Spray from 6 - 8 inches. Shake well before using. Select spray pattern by rotating nozzle to desired position. Spray evenly on both surfaces. Allow to dry 1 to 3 minutes, but not more than 30 minutes. Align and press surfaces together. Invert can and spray to clean nozzle. FEATURES AND BENEFITS • Fast drying. Will not attack foam. • Heat resistant. • High strength formula. • 3-way web spray nozzle (low, medium, high). • Temperature rated to 200°F.
RkJQdWJsaXNoZXIy MzE1MDc=