MATADOR (Tool Steel) PATRIOTWELDING RODS D13-4 REVISED JUNE, 2021 © Copyright 2023. All rights reserved. No portion may be copied or reproduced in any manner. TOOLS & SHOP SUPPLIES SOSMETAL PRODUCTS INC. D14 D13 D12 D11 HAWK (Steel) Extra low hydrogen electrode produces an exceptionally smooth, spatter free arc transfer on mild and low alloy steels. This electrode exhibits unusually good AC wedling characteristics, slag release and instant re-strike. APPLICATIONS: For joining and repairing of boiler plate, pipe steels, shipbuilding steels, and cast steels. Ideal for weathering steels and steels, such as “Corten”. Great for overlaying shafts and other worn parts. It is also used to repair and fabricate cold and hot rolled steels and most construction grades. Use on angle irons, beams, tanks and farm equipment. WELDING TECHNIQUES: Clean weld area and chamfer or bevel as needed. Maintain a short arc gap and use a stringer or slight weave technique. Chip slag thoroughly between passes. Peen weld immediately after breaking the arc. TYPICAL MECHANICAL PROPERTIES: Undiluted Weld Metal Maximum Value Up To Tensile strength 84,000 psi (610 N/mm2) Yield strength 69,000 psi (500 N/mm2) Elongation 32% Impact Energy 90J: (-30°C) WELDING POSITIONS: Flat, Vertical up, Vertical down, Horizontal, Overhead RECOMMENDED CURRENT: DC reverse (+) or AC DIAMETER PART REC. LENGTH ELECTRODES/ (INCHES) NUMBER AMPERAGE (INCHES) POUND 1/8 818197 95/140 14 12 5/32 818196 130/190 14 8 STINGER (Steel) Excellent for high strength steel structures that require toughness and crack resistance to temperatures as low as -76°F (-60°C). Low hydrogen, low temperature, extra low moisture content is below .14%. DIAMETER PART REC. LENGTH ELECTRODES/ (INCHES) NUMBER AMPERAGE (INCHES) POUND 3/32 818203 65/100 14 21 1/8 818204 100/140 14 12 APPLICATIONS: Nickel bearing low hydrogen designed for joining low alloy steels requiring high elongation combined with excellent low temperature impact values. WELDING TECHNIQUES: Remove all surface contaminants. Maintain a short arc gap and use a stringer or slight weave technique. Chip slag thoroughly between passes. WELDING POSITIONS: Flat, Vertical up, Vertical down, Horizontal, Overhead RECOMMENDED CURRENT: DC reverse (+) or AC TYPICAL MECHANICAL PROPERTIES: Undiluted Weld Metal Maximum Value Up To Tensile strength 92,000 psi (670 MPa) Yield strength 76,000 psi (500 MPa) Elongation 29% Impact energy 100J: -76°F (-60°C) 90J: -103°F (-75°C) 35J: -148°F (-100°C) Tubular large diameter chromium carbide rods for “hard facing”. Thin walled tubular construction allows for very low amperages. General wear protection on all iron base parts subject to abrasion. DIAMETER PART AMPERAGE LENGTH ELECTRODES/ (INCHES) NUMBER SETTINGS (INCHES) POUND 1/4 818404 100 18 5 3/8 818406 175 18 4 1/2 818408 215 18 3 APPLICATIONS: Matadors’ special bendable aluminum grip end caps allow for easy gripping & positioning of the electrode. Some typical applications include augers, bucket lips and chutes for transporting sand and gravel. WELDING TECHNIQUES: Using lowest possible amps and while holding the electrode 10° from the vertical position, deposit either stringer or weave beads. WELDING POSITIONS: Flat, Horizontal, Vertical up, Overhead RECOMMENDED CURRENT: DC reverse (+) or AC TYPICAL MECHANICAL PROPERTIES: Undiluted Weld Metal Maximum Value Up To Hardness Rockwell C57-60 Vickers 665-700 Wear Co-efficient 2%
RkJQdWJsaXNoZXIy MzE1MDc=